Model NO.: POM 90
Usage: General Plastics, Engineering Plastics, Specialty Plastics
Specification: ISO Certificate
CAS NO.:24969-26-4, 1,3,5-Trioxane,polymer with 1, 3-dioxolane
Copolyformaldehyde Resin, Copolyformaldehyde , Acetal copolymer, polyxymethylene, POM(Polyacetal) CAS NO.:24969-26-4, 1,3,5-Trioxane,polymer with 1, 3-dioxolane. Copolyformaldehyde (POM) is an excellent engineering plastics, in foreign countries have "wins Steel", "super steel" is called.
2. Usage .
POM has been widely used in electronic and electrical, mechanical , instruments, daily-use light industrial, automotive, building materials, agriculture and other fields. In many new fields of applications such as medical technology, sports equipment, etc., POM has a very low coefficient of friction and good geometric stability, particularly suited to the production of gears and bearings. It also has properties as a result of high temperature, it is also used pipe device (pipe valves, pump casing), lawn equipment, etc.
3. M90 Acetal Copolymer
General Material Status Standard-flow grade, with minimized mold deposit
Resistant Good Abrasion Resistance High Hardness Bacteria Resistant Good Chemical Resistance High Stiffness Base Resistant Good Dimensional Stability Low Friction
Solvent Resistant Good Electrical Properties Low Warpage Fatigue Resistant Good Flow
4.Uses: Automotive Electonics Fittings Thin-walled Parts Automotive Exterior Parts Gears Valves/Valve Parts Aumomotive Under the Hood pining Wheels Bearings Pump Parts
Forms: Pellets Processing Method: Injection Molding and Extrusion
6.Notes to users:
Values shown are based on testing of laboratory test specimens and represent data that fall within the standard range of properties for natural materal. These values alone do not represent a sufficient basis for any part design and are not intened for use in establing maximum, minimum, or ranges of values for specification purposes. Colorants or other additives may cause significant variations in data valuse.
7 Material Drying :
80-90C, 3-4 hours Cylinder Temperature: Nozzle :180-210 (C) Front Section :190-210 (C) Center Section : 170-200 (C) Rear Section : 160-180 (C) Melt Temperature : 180-210 (C) Mold Temperature : 60-90 (C) (Precision parts are often molede at a mold at a mold temperature as high as 120C) Pressure : Injection Pressure : 50-100 Mpa Holding Pressure : 30-80 Mpa Back Pressure:0-0.5 MPa Screw Rotational Speed : 50-120 rpm
Recommended Extruded Conditions Standard extruders with grooved feed zone and short compression screws (min. 25 D) will fit. Melt temperature : 180-190C
Acquired Certifications of POM RoHS test PFOS test Halogen element test SVHC test DMF test EN1186btest DBT&TBT test EN71-3 test Certification W18 test Certification FDA Certification UL
Contact us if you need more details on Pom. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Acetal Copolymer、Polyoxymethylene. If these products fail to match your need, please contact us and we would like to provide relevant information.
Ticona built the world's largest acetal plant
Ticona has recently built the world's largest acetal production plant in Frankfurt with an annual production capacity of more than 300 million pounds (about 136,000 tons). As the airport expansion required Ticona to relocate an existing acetal plant in Kelsterbach, Germany, the company decided to build the large-scale...
Preparation of Acrylic Copolymer Modified Corn Starch Adhesive
Abstract : The preparation method of corn starch adhesive modified by acrylic acid (AA)-acrylamide (AAm) copolymer was introduced. The effects of various factors such as polymerization temperature, AA-AAm copolymer, initiator and starch content, and pH on adhesive properties were studied. The modified adhesive exhibits good...
Development of Acrylic Copolymer Modified Corn Starch Adhesive II
2.1.3 Effect of AA-AAm Copolymer Dosage on Viscosity (see Figure 3) As can be seen from FIG. 3, the viscosity of the system increases as the amount of AA-AAm copolymer increases. Because AA and AAm are both very water-soluble, they can be easily polymerized into polymers. Copolymers contain hydrophilic groups such as -COOH,...
Ube Corporation develops new polyamide copolymer for packaging
At a recent International Packaging Exhibition held in Germany in 2005, Ube Corporation of Japan stated that the company has developed a new generation of polyamide materials using PA6, PA66 and PA12 ternary copolymers, mainly targeting meats, cereals and sausages. Packaging and other thermoformed film applications. Ube...
Product Categories : chemicals > Others chemicals